Configure on-prem agents for multisite deployment
In the earlier versions of NetScaler ADM, NetScaler instances deployed in remote data centers can be managed and monitored from NetScaler ADM running in a primary data center. NetScaler instances sent data directly to the primary NetScaler ADM that resulted in consumption of WAN bandwidth. Also, processing of analytics data utilizes CPU and memory resources of the primary NetScaler ADM.
You can have data centers located across the globe. Agents play a vital role in the following scenarios:
-
To install agents in remote data centers so that there is reduction in WAN bandwidth consumption.
-
To limit the number of instances directly sending traffic to primary NetScaler® ADM for data processing.
Note
-
Installing agents for instances in remote data center is recommended but not mandatory. If necessary, users can directly add NetScaler instances to primary NetScaler ADM.
-
If you have installed agents for one or more remote data centers, then the communication between the agents and the primary site is through floating IP address. For more information, see port.
-
You can install agents and apply pooled licenses to the instances at one or more remote data centers. In this scenario, the communication between the primary site and one or more remote data centers is through the floating IP address.
-
NetScaler ADM on-premises agent doesn't support pooled licensing.
From NetScaler ADM 12.1 or later, instances can be configured with agents to communicate with the primary NetScaler ADM located in a different data center.
Agents work as an intermediary between the primary NetScaler ADM and the discovered instances across different data centers. Following are the benefits of installing agents:
-
The instances are configured to agents so that the unprocessed data is sent directly to agents instead of primary NetScaler ADM. Agents do the first level of data processing and send the processed data in compressed format to the primary NetScaler ADM for storage.
-
Agents and instances are co-located in the same data center so that the data processing is faster.
-
Clustering the agents provides redistribution of NetScaler instances on agent failover. When one agent in a site fails, traffic from NetScaler instances is switched to another available agent in the same site.NoteThe number of agents to be installed per site depends on the traffic being processed.
Related information
Architecture
The following figure shows NetScaler instances in two data centers and NetScaler ADM high availability deployment using multisite agent-based architecture.
The primary site has the NetScaler ADM nodes deployed in a high availability configuration. The NetScaler instances in the primary site are directly registered with the NetScaler ADM.
In the secondary site, agents are deployed and registered with the NetScaler ADM server in the primary site. These agents work in a cluster to handle continuous flow of traffic in case an agent failover occurs. The NetScaler instances in the secondary site are registered with the primary NetScaler ADM server through agents located within that site. The instances send data directly to agents instead of primary NetScaler ADM. The agents process the data received from the instances and send it to the primary NetScaler ADM in a compressed format. Agents communicate with the NetScaler ADM server over a secure channel and the data sent over the channel is compressed for bandwidth efficiency.
Get started
-
Install the agent in a data center
-
Register the agent
-
Attach the agent to a site
-
-
Add NetScaler instances
-
Add new instance
-
Update an existing instance
-
Install the agent in a data center
You can install and configure the agent, to enable communication between the primary NetScaler ADM and the managed NetScaler instances in another data center.
You can install an agent on the following hypervisors in your enterprise data center:
-
Citrix Hypervisor™
-
VMware ESXi
-
Microsoft Hyper-V
-
Linux KVM Server
Note
On-prem agents for multisite deployment are supported only with NetScaler ADM high availability deployment.
Before you begin installing the agent, ensure you have the required virtual computing resources that the hypervisor must provide for each agent.
| Component | Requirement |
|---|---|
| RAM | 32 GB |
| Virtual CPU | 8 CPUs |
| Storage space | 30 GB |
| Virtual Network Interfaces | 1 |
| Throughput | 1 Gbps |
Ports
For communication purposes, the following ports must be open between the agent and NetScaler ADM on-prem server.
| Type | Port | Details | Direction of communication |
|---|---|---|---|
| TCP | 8443, 7443, 443 | For outbound and inbound communication between agent and the NetScaler ADM on-prem server. | NetScaler agent to NetScaler ADM |
The following ports must be open between the agent and NetScaler Instances.
| Type | Port | Details | Direction of communication |
|---|---|---|---|
| TCP | 80 | For NITRO communication between agent and NetScaler instance. | NetScaler ADM to NetScaler and NetScaler to NetScaler ADM |
| TCP | 22 | For SSH communication between agent and NetScaler instance. For synchronization between NetScaler ADM servers deployed in high availability mode. | NetScaler ADM to NetScaler and NetScaler agent to NetScaler |
| UDP | 4739 | For AppFlow communication between agent and NetScaler instance. | NetScaler to NetScaler ADM |
| ICMP | No reserved port | To detect network reachability between NetScaler ADM and NetScaler instances, or the secondary NetScaler ADM server deployed in high availability mode. | |
| UDP | 161, 162 | To receive SNMP events from NetScaler instance to agent. | Port 161 - NetScaler ADM to NetScaler |
| Port 162 - NetScaler to NetScaler ADM | |||
| UDP | 514 | To receive syslog messages from NetScaler instance to agent. | NetScaler to NetScaler ADM |
| TCP | 5557 | For Logstream communication between agent and NetScaler instances. | NetScaler to NetScaler ADM |
Register the agent
-
Use the agent image file downloaded from the NetScaler site and import it in to your hypervisor. The naming pattern of the agent image file is as follows, MASAGENT-\<HYPERVISOR\>-\<Version.no\>. For example: MASAGENT-XEN-13.0-xy.xva
-
From the Console tab, configure NetScaler ADM with the initial network configurations.
-
Enter the NetScaler ADM host name, IPv4 address, and gateway IPv4 address. Select option 7 to save and quit the configuration.
-
After the registration is successful, the console prompts to log on. Use nsrecover/nsroot as the credentials.
-
To register the agent, enter /mps/register\_agent\_onprem.py. The NetScaler agent registration credentials are displayed as shown in the following image.
-
Enter the NetScaler ADM floating IP address and the user credentials.
After the registration is successful, the agent restarts to complete the installation process.
After the agent restarts, access the NetScaler ADM GUI, from the main menu go to the Infrastructure > Instances > Agents page to verify the status of the agent. The newly added agent is displayed in Up state.
Note
The NetScaler ADM displays the version of the agent and also checks if the agent is on the latest version. The download icon signifies that the agent is not on the latest version and needs to be upgraded. Citrix recommends that you upgrade the agent version to the NetScaler ADM version.
Attach an agent to a site
-
Select the agent and click Attach Site.
-
In the Attach site page, select a site from the list, or create a site using the plus (+) button.
-
Click Save.Note
-
By default, all newly registered agents are added to the default data center.
-
It is important to associate the agent with the correct site. In the event of an agent failure, the NetScaler instances assigned to it are automatically switched to other functioning agents in the same site.
-
Agent actions
You can apply various actions to an agent under Infrastructure > Agents > Select Actions.
Under Select Action, you can use the following features:
Install a new certificate: if you need a different agent certificate to meet your security requirement, you can add one.
Change the default password: to ensure security of your infrastructure, change the default password of an agent.
Generate a technical support file: generate a technical support file for a selected NetScaler agent. You can download this file and send it to Citrix technical support for investigation and troubleshooting.
Add NetScaler instances
Instances are NetScaler ADC appliances or virtual appliances that you want to discover, manage, and monitor from NetScaler ADM through agents. You can add the following NetScaler ADC appliances and virtual appliances to NetScaler ADM or agents:
-
NetScaler MPX
-
NetScaler VPX
-
NetScaler SDX
-
NetScaler CPX
-
NetScaler Gateway
-
Citrix SSL Forward Proxy
For more information, see Add instances to NetScaler ADM.
Attach an existing instance to the agent
If an instance is already added to the primary NetScaler ADM, you can attach it to an agent by editing an agent.
-
Navigate to Infrastructure > Instances and select the instance type. For example, NetScaler.
-
Click Edit to edit an existing instance.
-
Click to select the agent.
-
From the Agent page, select the agent with which you want to associate the instance and then click OK.NoteEnsure to select the Site with which you want to associate the instance.
Access the GUI of an instance to validate events
After the instances are added and agent is configured, access the GUI of an instance to check if the trap destination is configured.
In NetScaler ADM, navigate to Infrastructure > Instances. Under Instances, select the type of instance you want to access (for example, NetScaler VPX), and then click the IP address of a specific instance.
The GUI of the selected instance is displayed in a pop-up window.
By default, the agent is configured as the trap destination on the instance. To confirm, log on to the GUI of the instance and check the trap destinations.
Important
Adding an agent for NetScaler instances in remote data centers is recommended but not mandatory.
In case you want to add the instance directly to the primary MAS, do not select an agent while adding instances.
NetScaler agent failover
The agent failover can occur in a site that has two or more registered agents. When an agent becomes inactive (DOWN state) in the site, the NetScaler ADM redistributes the ADC instances of the inactive agent with other active agents.
Important
-
Ensure the Agent Failover feature is enabled on your account. To enable this feature, see Enable or disable ADM features.
-
If an agent is running a script, ensure that script is present on all the agents in the site. Therefore, the changed agent can run the script after agent failover.
To attach a site to an agent in the ADM GUI, see Attach an agent to a site.
To achieve an agent failover, select NetScaler agents one by one and attach to the same site.
For example, two agents 10.106.1xx.2x and 10.106.1xx.3x are attached and operational in the Bangalore site. If one agent becomes inactive, NetScaler ADM detects it and displays the state as down.
When a NetScaler agent becomes inactive (Down state) in a site, NetScaler ADM waits for five minutes for the agent to become active (Up state). If the agent remains inactive, NetScaler ADM automatically redistributes the instances among available agents in the same site.
NetScaler ADM triggers instance redistribution every 30 minutes to balance the load among active agents in the site.
Configure agent unreachable threshold and notification
If an agent is down or not reachable for a certain duration, you can get notification on the agent status through email, slack, PagerDuty, and ServiceNow. In Infrastructure > Instances > Agents, click Settings, specify the duration between 5 minutes and 60 minutes, and select the notification method that you want to get notified.
